- #Kenwood tk 880 vs tk880h serial#
- #Kenwood tk 880 vs tk880h software#
- #Kenwood tk 880 vs tk880h windows#
Note: The following preparation instructions are for use by your KENWOOD dealer, an authorized KENWOOD service facility, or the factory. VEHICLE AND ENLIST HIS AID IN DETERMINING IF THEY WILL PERFORM NORMALLY WHILE TRANSMITTING. IF YOUR VEHICLE CONTAINS SUCH EQUIPMENT, CONSULT THE DEALER FOR THE MAKE OF ELECTRONIC FUEL INJECTION, ANTI-SKID BRAKING, AND CRUISEĬONTROL SYSTEMS ARE TYPICAL EXAMPLES OF EQUIPMENT THAT MAY MALFUNCTION. NOT PROPERLY PROTECTED FROM THE RADIO FREQUENCY ENERGY WHICH IS PRESENT VARIOUS ELECTRONIC EQUIPMENT IN YOUR VEHICLE MAY MALFUNCTION IF THEY ARE Reviewing Messages in the Queue Memory.Īutomatic Status Response. Do not transmit while the caps are being placed into or removed from the container. If you are transporting blasting caps in your vehicle, make sure they are carried in a closed metal box with a padded interior. Turn OFF your transceiver when in an area where blasting is in progress, or where “TURN OFF TWO-WAY RADIO” signs have been posted. Operating the transceiver within 500 feet of dynamite blasting caps may cause them to explode. INJURY FROM RADIO FREQUENCY TRANSMISSIONSĭo not operate your transceiver when somebody is either touching the antenna or standing within two to three feet of it, to avoid the possibility of radio frequency burns or related physical injury. Do not carry spare fuel containers in the trunk of your vehicle if your transceiver is mounted in the trunk area. Turn OFF your transceiver while taking on fuel or while parked in a gasoline service station. SAFETY: It is important that the operator is aware of, and understands, hazards common to the operation of any transceiver.ĮXPLOSIVE ATMOSPHERES (GASES, DUST, FUMES, etc.) REFER SERVICE TO QUALIFIED TECHNICIANS ONLY. ILLEGAL OPERATION IS PUNISHABLE BY FINE AND/OR IMPRISONMENT. GOVERNMENT LAW PROHIBITS THE OPERATION OF UNLICENSED RADIO TRANSMITTERS WITHIN THE TERRITORIES UNDER GOVERNMENT CONTROL. Ï If an abnormal odour or smoke is detected coming from the transceiver, turn OFF the power immediately. Ï Do not place the transceiver in excessively dusty, humid, or wet areas, nor on unstable surfaces. Ï Do not expose the transceiver to long periods of direct sunlight, nor place it near heating appliances. Ï Do not modify the transceiver for any reason. Ï Do not attempt to configure the transceiver while driving it is too dangerous. Please observe the following precautions to prevent fire, personal injury, and transceiver damage. As a result, we feel strongly that you will be pleased with the quality and features of this product. KENWOOD transceivers incorporate the latest in advanced technology. We believe this easy-to-use transceiver will provide dependable communications to keep personnel operating at peak efficiency.
#Kenwood tk 880 vs tk880h software#
Kenwood programming software reference for the TK-880 Recommended Software: KPG-49D Version 4įor the European version of the K-880 you will instead use the KPG-60D DOS software with the same KPG-46 cable.
#Kenwood tk 880 vs tk880h windows#
The KPG-49D Version 2.(any number) and 3.(any number) are DOS based, while version 4.(any number) are Windows based and much easier to use. Re-align the radio for optimum performance on 70cm. It is said that most Kenwood LMRS 450-490 radios will go to about 442-443 mhz, but the VCO can easily be adjusted to go lower. The 70cm amateur radio band is the 420 to 450 MHz portion of the UHF radio spectrum. The TK-880 will program below 450 MHz, but the receive sensitivity is reduced.
#Kenwood tk 880 vs tk880h serial#
The cable is serial on one end and RJ45 on the other. The last released KPG-49D software runs under Windows. The KPG-49D software can program all radios in the TK-X80 series. You need the KPG-49D programming software and an appropriate cable. 1.2 kenwood programming software reference for the TK-880.